The shape of things to come

Well, after the whole glue up scare I was able to pull myself together and start shaping my board. This, I have to admit, was a little nerve wracking because you spend all this time putting all of these pieces together and then now you have to take a blade to it and start cutting it down. Breath! Just do as the manual says and take it one step at a time.

Trying to take it slow so that I can always come back and remove more material. As a wood worker I learned long ago that you don't have a lot of sucess putting the wood back on after you remove it. This is also where my lack of knowledge starts to play evil tricks with me. Other than the directions in the manual and my small amount of experience surfing, I havn't the first clue how to shape a boards rails. Up until this point the rails were folowing the shape of the frames, but now I must fly solo and just let my instincts take over and trust that I have gleaned enough from the Grain super manual. Have you ever noticed that you can read something over and over and it still makes no sence to you, and then when you have left it and come back it all of a sudden is crystal clear ( well maybe crystal is an over statement ).

I did a little playing and came up with a configureation for the tail block that I feel looks good with the boards stringer and jumped right into cutting the ass off of my board. Just go for it! Everyone who has built a board has had to do the same thing, I am not the first. I'm sure I'm not the first guy or girl to get a little nervous as the process continues. Every hour you put into the project is one more step closer to something that you don't want to screw up!

Glue the blocking! Glue the blocking to the board! Shape the blocking!

Hey! Wait a minute! This is starting to look like a surf board!

The Great 3M Debacle! Well, almost.

This story begins about twenty three and a half hours after I glued the top plank onto my board. The glue up went very smoothly, as planned (everyone should do a dry run before doing something this involved and important). I very patiently waited the day through to take off the 100 clamps that were holding the board together (you truly can never have too many clamps).

Once all of the clamps were off I stood back and admired all of the hard work I had put in and all of the patience I had given to the board. I picked the board up, I tucked it under the arm dreaming of the first time I will take it out, I ran my hands over its surfaces (WAIT A MINUTE! What is this)?

The keel section at the nose with the most camber is not adhered to the deck! 

What happened?

Most importantly, WHAT DO I DO?

I did the only thing I knew to do. Put the clamps back on as quickly as possible. It was too late to call Grain that day, so I waited and tried to not think about it until the next day. After having a fitful night I got in touch with Mike at Grain and his tone put me at ease. We discussed what exactly happened and found out that if you have to buy a second tube of 3M 5200 you have to make sure you get the fast cure and not the 7 day cure version if you want to take the clamps off after 24 hrs. Otherwise, You have to wait a full week. That was O.K. because I had other things to do, but when you get on a role and you are at this stage of the build you don't want to have wait a week for anything.

Well, I don't know if you can tell or not from the picture, but everything worked out. This really taught me a lot. I learned that you should always read directions no matter how much of a hurry you are in. Follow the directions. Never assume anything is good until you check it for yourself (if I would have walked away from the board with out really looking it over I would have missed the issue and come back after the weekend to horrific disappointment). And finally, I learned, and I have been learning throughout this entire project, that if you slowdown and take it one step at a time and not get ahead of yourself everything will turn out fine.

The end is the beginning is the process

So this is where we pick up where we left off. I've been a little lame with my posting and my board building until lately. Since my last post so many things have happened. I went back country fishing in Kodiak, Alaska. This turned out to be one of the greatest adventures yet. Four nights in the wild in a tent and the best bunch of guys you could ask for.

I came home with a freezer full of salmon and a burning desire to go back (I think 2013). Then I spent a little time in one of my favorite states, Washington. My wife and I went to what we would find out to be the last Journalfest in Port Townsend. We were able to spend some great days with what I consider some of the best friends you could ask for. After the Holidays we went to Florida to see family in  two locations up and down the coast with a little majic in the middle. That's right, we went to Harry Potter World at Universal Studios Orlando. Good times and great relaxation. March saw me back in Washington for the final Artfest and more creative time with great friends. Then, May. Trip to Texas to see more family and friends. It's the first week in May and I am not ready for 90 degree weather. I guess that is why I moved out of Texas.

Well while all of this was going on I did manage to get a little work done on my waterlog. First I moved the whole shooting match up to my shop where I work so I could have some heat during the winter months, it is Colorado. I have to admit I got a little bogged down with the railing process but eventually got some steam and finished the glue up. I don't know how they teach this class in a week. I guess I am just a little too retentive to work that fast.

After this I got to start some pre shaping and really got to start seeing the fruits of my labor.

Next Time we'll talk about the top and how much fun it is to get to the point where foam board builders start their boards.